Back to Blog
Webcam setup in repetier server5/31/2023 ![]() The Repetier-Firmware also supports a binary format. All supported firmwares work in ASCII mode. The transfer protocol determines, how the host will communicate with the printer. Stop bits and parity are correct for 99,9% of the printer, so leave them untouched. Then select the baud rate entered into the firmware. If you connect your printer when this menue is already open, klick “Refresh Ports” to detect the new port. At the opening of the window, all available ports were scanned and added to the list. In “Port” you select the port, where your printer is connected. In this first tab, you set how to connect with your printer. These can be changed in the g-code editor, which is described in a different chapter. In addition to this, for each configuration a start/end/pause/kill and five user defines scripts are stored with configuration. The new printer will start with the same settings as the last selected printer.īelow the drop down box you see four tabs with most off the data stored with the printer configuration. To create a new printer you only need to change the printer name and press “Apply”. At the start you have only the default printer. You will see a window like this:Īt the top you see a drop down box, with the currently selected printer. Go to the menu “Config”->”Printer Settings” or klick the button. If you have uploaded the firmware to your printer, the driver is already installed. Some printer need special driver to access the device, so make sure the drivers are also installed. Make sure your printer is connected and enabled. The next step should be, to configure your printer so you can connect your computer with the host. The work directory is, where the host will put temporary stl files, sliced results and if enabled the log file. You can select any directory, where you have write privileges, but it is advised to use a separate directory for this purpose. The latest windows versions skip this step, because the installer already created a work directory for you. On Debian you can call:Īfter the first start a dialog may pop up asking you, where your work directory should be. You need to put your user into the right group. One problem that most linux distributions have is, that the normal users are not allowed to connect to a serial console. If you are in doubt, install Mono develop, which has all needed libraries as dependency. Make sure you have all required Mono libraries installed. ![]() Move it to where you want your files and unpack its contents and run the post installation script:Īfter that you have a link in /usr/bin to the installation, so you can start it with repetierHost. The linux version comes as gzipped tar file. The installer already contains Slic3r and Skeinforge for slicing and python and pypy, which are needed to run Skeinforge. After downloading run the installer and you are done. The windows version comes with a installer. Go to the download page and fetch the latest version for your os. With lower versions you may have speed issues with live preview. For a good rendering performance OpenGL 1.5 or higher is needed. The only other requirement is a graphic card with OpenGL. ![]() NET framework 4.0 or a recent Mono installation, if you are running Linux. If you have a Macintosh computer, check for the Repetier-Host Mac on this site. The Host works on Windows XP and later and on Linux. ![]() If you have an old computer running Windows XP you may have difficulties. Currently available computers should have no problems at all. It just wrappes the public API into an app.Before you start with the installation, you should check if your computer meets the requirements. This app is not associated with Repetier Server Pro or Hot-World GmbH & Co. An additional license is needed to run Repetier Server Pro! Repetier Server Pro is owned and developed by Hot-World GmbH & Co. This app needs Repetier Server Pro in order to work. This version comes with some pro-only functions and does not show any ads. This is the pro version of our Remote Controll App for Repetier Server Pro. Live-view what your printer is doing (needs a WebCam installed) Manage your models and print, pause or stop just with one click Remote control your printer directly from your smartphone ![]() See current print progress and remaining print duration If you want to connect your server from outside of your local network, you need to setup a VPN connection. You'are an 3d printing enthusiast and you're using Repetier Server Pro for controlling your 3d printers? Then this app is the perfect addition! If you want to try this app first, please use the free version which is also available in the App Store. ![]()
0 Comments
Read More
Leave a Reply. |